+34 637 212 975 Mon–Fri 8:00–17:00 Madrid time Wishlist0 Compare0
€0.00
1315 · 75 × 160 × 37

Self-aligning ball · 1315

radial — mediumaxial — low, on both sides
    Drawing of 1315: ⌀75 × ⌀160 × 37 mm⌀160⌀75371315
    Fig. 1: 1315, end view and section; internal parts simplified per ISO 8826-1. Dimensions in mm

    There is no photo of this product: the 3D model and drawing show the dimensions of 1315

    Load: radial medium; axial low, on both sidesSelf-aligning ball

    Bearing SKF 1315

    Price on request
    Available to order
    Request a quoteIn the cart: send the request

    Specifications

    Manufacturer number
    Equivalents
    4 exact, 6 approximate
    d
    75 mm
    Bore diameter dBearing bore = shaft diameter. Source: supplier data
    D
    160 mm
    Outside diameter DOutside diameter = housing bore. Source: supplier data
    B
    37 mm
    Width BRing width. Source: supplier data
    Seal
    open, no protection
    Clearance
    normal clearance
    C
    79.3 kN
    Basic dynamic load rating CLoad for one million revolutions at 90 % reliability; the L10 life is calculated from it as (C/P)^p. ISO method, manufacturer’s figure: do not carry it over to another brand. Source: supplier data
    01

    Equivalents

    the same size 75 × 160 × 37 from other brands

    10 products
    Series illustration (not a photo of this item): 1315
    You are viewingSKF 1315

    Everything the number specifies matches: series 13, 75 × 160 × 37 mm, open, no protection, normal clearance, ordinary steel, design without special letters. The codes in the number are read against the SKF catalogue.

    • Series illustration (not a photo of this item): 13151315This bearingSKF75 × 160 × 37available to orderon requestyou are here
    • Photo: 13151315ZKL75 × 160 × 37available to order€74.66
    • Series illustration (not a photo of this item): 13151315NSK75 × 160 × 37available to orderon request
    • Series illustration (not a photo of this item): 13151315NTN/SNR75 × 160 × 37available to orderon request
    02

    Details

    what this bearing is, questions

    About the bearing

    d×D×Bsize 75 × 160 × 37mm
    Cdynamic 79.3kN

    Self-aligning ball bearing 1315. Under GOST the same bearing is designated 1315.

    C: SKF data. Another brand publishes its own figures, so compare them against that brand’s catalogue.

    Frequently asked questions

    What is 1315?

    It is the same bearing under GOST 3189-89: 1315 corresponds to the ISO base 1315. Size 75 × 160 × 37 mm, a full equivalent of 1315.

    Will 1315 C3 fit instead?

    Same size, clearance greater than normal. C3 is used where the bearing runs hot or sits on the shaft with an interference fit. If the old bearing is not marked C3, take this one.

    Can I fit another brand instead of this bearing?

    Without checking, only an exact equivalent: the size, seal, clearance and design match according to the brand’s catalogue. Positions with the same geometry differ in seal, clearance or design, and each one says so in the equivalents block. Load ratings differ between manufacturers, so for a heavily loaded unit compare C.

    How do I get a price and a lead time?

    Press “Request a quote” and send the part number and quantity. We reply with the price, availability and delivery terms for your country.

    03

    Reviews

    No reviews yet