+34 637 212 975 Mon–Fri 8:00–17:00 Madrid time Wishlist0 Compare0
€0.00
1307 EKTN9 · 35 × 80 × 21

Self-aligning ball · 1307 EKTN9

radial — mediumaxial — low, on both sides
    Drawing of 1307 EKTN9: ⌀35 × ⌀80 × 21 mm⌀80⌀35211307 EKTN9
    Fig. 1: 1307 EKTN9, end view and section; internal parts simplified per ISO 8826-1. Dimensions in mm

    There is no photo of this product: the 3D model and drawing show the dimensions of 1307 EKTN9

    Load: radial medium; axial low, on both sidesSelf-aligning ball

    Bearing SKF 1307 EKTN9

    Price on request
    Available to order
    Request a quoteIn the cart: send the request

    Specifications

    Manufacturer number
    ISO designation
    Equivalents
    3 exact, 10 approximate
    d
    35 mm
    Bore diameter dBearing bore = shaft diameter. Source: supplier data
    D
    80 mm
    Outside diameter DOutside diameter = housing bore. Source: supplier data
    B
    21 mm
    Width BRing width. Source: supplier data
    Seal
    open, no protection
    Clearance
    normal clearance
    C
    26.5 kN
    Basic dynamic load rating CLoad for one million revolutions at 90 % reliability; the L10 life is calculated from it as (C/P)^p. ISO method, manufacturer’s figure: do not carry it over to another brand. Source: supplier data
    01

    Equivalents

    the same size 35 × 80 × 21 from other brands

    15 products
    Series illustration (not a photo of this item): 1307 EKTN9
    You are viewingSKF 1307 EKTN9

    Everything the number specifies matches: series 13, 35 × 80 × 21 mm, open, no protection, K, normal clearance, special design. The codes in the number are read against the SKF catalogue.

    • Series illustration (not a photo of this item): 1307 EKTN91307 EKTN9This bearingSKF35 × 80 × 21available to orderon requestyou are here
    • Series illustration (not a photo of this item): 1307 K1307 KCT35 × 80 × 213 pcs€2.83
    • Series illustration (not a photo of this item): 1307 K1307 KNSK35 × 80 × 21available to orderon request
    02

    Often bought with this

    adapter sleeve H307, lock nut M35×1.5, lock washer MB07, bore snap ring Ø80

    8 products
    • Adapter sleeve H307CT H 307Why it fits: H307 for 1307 K: 1:12 taper, bore 35 for shaft 30 (Koyo, p. 65)
      €1.4986 pcs
    • Adapter sleeve H307FAG H 307Why it fits: H307 for 1307 K: 1:12 taper, bore 35 for shaft 30 (Koyo, p. 65)
      Price to be confirmedavailable to order
    • Lock nut M35×1.5KM 07Why it fits: KM07 is the nut for sleeve H307: thread M35×1.5
      €0.82available to order
    • Lock nut M35×1.5Z&S KM 7Why it fits: KM07 is the nut for sleeve H307: thread M35×1.5
      €0.98available to order
    • Lock washer MB07CT MB 07Why it fits: MB07 locks the KM07 nut (ISO 2982-2)
      €0.106,655 pcs
    • Lock washer MB07NEU MB 7Why it fits: MB07 locks the KM07 nut (ISO 2982-2)
      €0.17available to order
    • Bore snap ring Ø80CT SEG 80 W by 100Why it fits: DIN 472 snap ring for a 80 bore: holds the outer ring in the housing
      €21.42out of stock
    • Bore snap ring Ø80SEG 80 W by 100Why it fits: DIN 472 snap ring for a 80 bore: holds the outer ring in the housing
      Price to be confirmedavailable to order
    03

    Details

    what this bearing is, questions

    About the bearing

    d×D×Bsize 35 × 80 × 21mm
    Cdynamic 26.5kN

    Self-aligning ball bearing 1307 K.

    C: SKF data. Another brand publishes its own figures, so compare them against that brand’s catalogue.

    Frequently asked questions

    Will 1307 C3 fit instead?

    Same size, clearance greater than normal. C3 is used where the bearing runs hot or sits on the shaft with an interference fit. If the old bearing is not marked C3, take this one.

    Can I fit another brand instead of this bearing?

    Without checking, only an exact equivalent: the size, seal, clearance and design match according to the brand’s catalogue. Positions with the same geometry differ in seal, clearance or design, and each one says so in the equivalents block. Load ratings differ between manufacturers, so for a heavily loaded unit compare C.

    How do I get a price and a lead time?

    Press “Request a quote” and send the part number and quantity. We reply with the price, availability and delivery terms for your country.

    04

    Reviews

    No reviews yet