+34 637 212 975 Mon–Fri 8:00–17:00 Madrid time Wishlist0 Compare0
€0.00
6315-2RS1 · 75 × 160 × 37

Deep groove ball · 6315-2RS1

radial — mediumaxial — low, on both sides
    Drawing of 6315-2RS1: ⌀75 × ⌀160 × 37 mm6315-2RS12RS1
    Fig. 1: 6315-2RS1, end view and section; rolling element geometry per the NSK catalogue. Dimensions in mm

    There is no photo of this product: the 3D model and drawing show the dimensions of 6315-2RS1

    Load: radial medium; axial low, on both sidesDeep groove ball

    Bearing SKF 6315-2RS1

    Price on request
    Available to order
    Request a quoteIn the cart: send the request

    Specifications

    Manufacturer number
    ISO designation
    GOST number
    Equivalents
    5 exact, 18 approximate
    d
    75 mm
    Bore diameter dBearing bore = shaft diameter. Source: supplier data
    D
    160 mm
    Outside diameter DOutside diameter = housing bore. Source: supplier data
    B
    37 mm
    Width BRing width. Source: supplier data
    Seal
    2RS1contact seals on both sides
    Clearance
    normal clearance
    C
    119 kN
    Basic dynamic load rating CLoad for one million revolutions at 90 % reliability; the L10 life is calculated from it as (C/P)^p. ISO method, manufacturer’s figure: do not carry it over to another brand. Source: supplier data
    01

    Equivalents

    the same size 75 × 160 × 37 from other brands

    23 products
    Series illustration (not a photo of this item): 6315-2RS1
    You are viewingSKF 6315-2RS1

    Everything the number specifies matches: series 63, 75 × 160 × 37 mm, contact seals on both sides, normal clearance, ordinary steel, design without special letters. The codes in the number are read against the SKF catalogue.

    • Series illustration (not a photo of this item): 6315-2RS16315-2RS1This bearingSKF75 × 160 × 37available to orderon requestyou are here
    • Series illustration (not a photo of this item): 6315 2RS6315 2RSCT75 × 160 × 37157 pcs€12.74
    • Photo: 6315 2RS6315 2RSZ&S75 × 160 × 37available to order€23.07
    • Series illustration (not a photo of this item): 6315-2RS6315-2RSDYZV75 × 160 × 37available to orderon request
    • Series illustration (not a photo of this item): 6315 2RS6315 2RSKG75 × 160 × 37available to orderon request
    02

    Details

    what this bearing is, questions

    Where this bearing is fitted

    2 machines1 makeby parts catalogues

    1. Belarus 80/​82 (80.1/​80.3/​80U/​82U/​82.1/​820/​82.3/​82R/​82P) Belarus same geometry 1 assembly · 2 pcs per machine

      ours: seals on both sides (2RS); in the machine: open

      manufacturer’s catalogue: BELARUS 80.1/​80.3/​80U/​82U/​82.1/​820/​82.3/​82R/​82P. 80-0000010 KDS. Catalogue of parts and assembly units, ed. 10 (RUE MTZ)

    2. Belarus-80Kh/​80Kh.1/​100Kh Belarus same geometry 1 assembly · 2 pcs per machine

      ours: seals on both sides (2RS); in the machine: open

      manufacturer’s catalogue: BELARUS-80Kh/​80Kh.1/​100Kh. 80Kh-0000010 KDS. Catalogue of assembly units and parts (RUE MTZ, 2012)

    Number in the manufacturer’s catalogue: by GOST (180315) or ISO. “Same geometry” means size and type match; the version is not given in the catalogue.

    About the bearing

    D 160d 75B 37
    d×D×Bsize 75 × 160 × 37mm
    Cdynamic 119kN

    Deep groove ball bearing 6315-2RS, design 2RS1: contact seals on both sides. Under GOST the same bearing is designated 180315.

    C: SKF data. Another brand publishes its own figures, so compare them against that brand’s catalogue.

    Frequently asked questions

    How does 2RS differ from ZZ?

    2RS has rubber seals that touch the inner ring and keep out dust and water better, which is the usual choice for field machinery. ZZ has metal shields that do not touch, allow higher speeds, and protect against dirt less well.

    What is 180315?

    It is the same bearing under GOST 3189-89: 18 — contact seals on both sides, 0315 corresponds to the ISO base 6315. Size 75 × 160 × 37 mm, a full equivalent of 6315-2RS.

    Will 6315 2RS1 C3 fit instead?

    Same size, clearance greater than normal. C3 is used where the bearing runs hot or sits on the shaft with an interference fit. If the old bearing is not marked C3, take this one.

    Can I fit another brand instead of this bearing?

    Without checking, only an exact equivalent: the size, seal, clearance and design match according to the brand’s catalogue. Positions with the same geometry differ in seal, clearance or design, and each one says so in the equivalents block. Load ratings differ between manufacturers, so for a heavily loaded unit compare C.

    How do I get a price and a lead time?

    Press “Request a quote” and send the part number and quantity. We reply with the price, availability and delivery terms for your country.

    03

    By make and unit

    this bearing is fitted in machines of these makes

    04

    Reviews

    No reviews yet