+34 637 212 975 Mon–Fri 8:00–17:00 Madrid time Wishlist0 Compare0
€0.00
2209 EKTN9 · 45 × 85 × 23

Self-aligning ball · 2209 EKTN9

radial — mediumaxial — low, on both sides
    Drawing of 2209 EKTN9: ⌀45 × ⌀85 × 23 mm⌀85⌀45232209 EKTN9
    Fig. 1: 2209 EKTN9, end view and section; internal parts simplified per ISO 8826-1. Dimensions in mm

    There is no photo of this product: the 3D model and drawing show the dimensions of 2209 EKTN9

    Load: radial medium; axial low, on both sidesSelf-aligning ball

    Bearing SKF 2209 EKTN9

    Price on request
    Available to order
    Request a quoteIn the cart: send the request

    Specifications

    Manufacturer number
    ISO designation
    Equivalents
    2 exact, 17 approximate
    d
    45 mm
    Bore diameter dBearing bore = shaft diameter. Source: supplier data
    D
    85 mm
    Outside diameter DOutside diameter = housing bore. Source: supplier data
    B
    23 mm
    Width BRing width. Source: supplier data
    Seal
    open, no protection
    Clearance
    normal clearance
    C
    32.5 kN
    Basic dynamic load rating CLoad for one million revolutions at 90 % reliability; the L10 life is calculated from it as (C/P)^p. ISO method, manufacturer’s figure: do not carry it over to another brand. Source: supplier data
    01

    Equivalents

    the same size 45 × 85 × 23 from other brands

    19 products
    Cross-section drawing to size: Self-aligning ball, 45 × 85 × 23 mm
    You are viewingSKF 2209 EKTN9

    Everything the number specifies matches: series 22, 45 × 85 × 23 mm, open, no protection, K, normal clearance, special design. The codes in the number are read against the SKF catalogue.

    • Cross-section drawing to size: Self-aligning ball, 45 × 85 × 23 mm2209 EKTN9This bearingSKF45 × 85 × 23available to orderon requestyou are here
    • Photo: 2209 K2209 KZ&S45 × 85 × 23available to order€10.24
    02

    Often bought with this

    adapter sleeve H309, lock nut M45×1.5, lock washer MB09, bore snap ring Ø85, seal 40×85

    8 products
    • Adapter sleeve H309CT H 309 SILVERWhy it fits: H309 for 2209 K: 1:12 taper, bore 45 for shaft 40 (Koyo, p. 65)
      €2.0738 pcs
    • Adapter sleeve H309CT H 309 WITH BLACK KMWhy it fits: H309 for 2209 K: 1:12 taper, bore 45 for shaft 40 (Koyo, p. 65)
      €2.09available to order
    • Lock nut M45×1.5CT KM 09 (ocynk)Why it fits: KM09 is the nut for sleeve H309: thread M45×1.5
      €0.54112 pcs
    • Lock nut M45×1.5KM 09Why it fits: KM09 is the nut for sleeve H309: thread M45×1.5
      Price to be confirmedavailable to order
    • Lock washer MB09CT MB 09Why it fits: MB09 locks the KM09 nut (ISO 2982-2)
      €0.18598 pcs
    • Lock washer MB09NEU MB 9Why it fits: MB09 locks the KM09 nut (ISO 2982-2)
      €0.25available to order
    • Bore snap ring Ø85CT SEG 85 W by 100Why it fits: DIN 472 snap ring for a 85 bore: holds the outer ring in the housing
      €22.57out of stock
    • Seal 40×85JULU 040-85-10 TCWhy it fits: Oil seal 40×85: sleeve shaft 40, housing bore for the bearing 85; SN/SNL housings have their own seals, so check against the housing
      €0.57699 pcs
    03

    Details

    what this bearing is, questions

    About the bearing

    d×D×Bsize 45 × 85 × 23mm
    Cdynamic 32.5kN

    Self-aligning ball bearing 2209 K.

    C: SKF data. Another brand publishes its own figures, so compare them against that brand’s catalogue.

    Frequently asked questions

    Will 2209 C3 fit instead?

    Same size, clearance greater than normal. C3 is used where the bearing runs hot or sits on the shaft with an interference fit. If the old bearing is not marked C3, take this one.

    Can I fit another brand instead of this bearing?

    Without checking, only an exact equivalent: the size, seal, clearance and design match according to the brand’s catalogue. Positions with the same geometry differ in seal, clearance or design, and each one says so in the equivalents block. Load ratings differ between manufacturers, so for a heavily loaded unit compare C.

    How do I get a price and a lead time?

    Press “Request a quote” and send the part number and quantity. We reply with the price, availability and delivery terms for your country.

    04

    Reviews

    No reviews yet