+34 637 212 975 Mon–Fri 8:00–17:00 Madrid time Wishlist0 Compare0
€0.00
2207 EKTN9 · 35 × 72 × 23

Self-aligning ball · 2207 EKTN9

radial — mediumaxial — low, on both sides
    Drawing of 2207 EKTN9: ⌀35 × ⌀72 × 23 mm⌀72⌀35232207 EKTN9
    Fig. 1: 2207 EKTN9, end view and section; internal parts simplified per ISO 8826-1. Dimensions in mm

    There is no photo of this product: the 3D model and drawing show the dimensions of 2207 EKTN9

    Load: radial medium; axial low, on both sidesSelf-aligning ball

    Bearing SKF 2207 EKTN9

    Price on request
    Available to order
    Request a quoteIn the cart: send the request

    Specifications

    Manufacturer number
    ISO designation
    GOST number
    Equivalents
    2 exact, 15 approximate
    d
    35 mm
    Bore diameter dBearing bore = shaft diameter. Source: supplier data
    D
    72 mm
    Outside diameter DOutside diameter = housing bore. Source: supplier data
    B
    23 mm
    Width BRing width. Source: supplier data
    Seal
    open, no protection
    Clearance
    normal clearance
    C
    30.7 kN
    Basic dynamic load rating CLoad for one million revolutions at 90 % reliability; the L10 life is calculated from it as (C/P)^p. ISO method, manufacturer’s figure: do not carry it over to another brand. Source: supplier data
    01

    Equivalents

    the same size 35 × 72 × 23 from other brands

    18 products
    Cross-section drawing to size: Self-aligning ball, 35 × 72 × 23 mm
    You are viewingSKF 2207 EKTN9

    Everything the number specifies matches: series 22, 35 × 72 × 23 mm, open, no protection, K, normal clearance, special design. The codes in the number are read against the SKF catalogue.

    • Cross-section drawing to size: Self-aligning ball, 35 × 72 × 23 mm2207 EKTN9This bearingSKF35 × 72 × 23available to orderon requestyou are here
    • Cross-section drawing to size: Self-aligning ball, 35 × 72 × 23 mm2207 Kno brand35 × 72 × 23available to orderon request
    02

    Often bought with this

    adapter sleeve H307, lock nut M35×1.5, lock washer MB07, bore snap ring Ø72, seal 30×72

    8 products
    • Adapter sleeve H307CT H 307Why it fits: H307 for 2207 K: 1:12 taper, bore 35 for shaft 30 (Koyo, p. 65)
      €1.4986 pcs
    • Adapter sleeve H307FAG H 307Why it fits: H307 for 2207 K: 1:12 taper, bore 35 for shaft 30 (Koyo, p. 65)
      Price to be confirmedavailable to order
    • Lock nut M35×1.5KM 07Why it fits: KM07 is the nut for sleeve H307: thread M35×1.5
      €0.82available to order
    • Lock nut M35×1.5Z&S KM 7Why it fits: KM07 is the nut for sleeve H307: thread M35×1.5
      €0.98available to order
    • Lock washer MB07CT MB 07Why it fits: MB07 locks the KM07 nut (ISO 2982-2)
      €0.106,655 pcs
    • Lock washer MB07NEU MB 7Why it fits: MB07 locks the KM07 nut (ISO 2982-2)
      €0.17available to order
    • Bore snap ring Ø72CT SEG 72 W by 1000Why it fits: DIN 472 snap ring for a 72 bore: holds the outer ring in the housing
      €177.06available to order
    • Seal 30×72JULU 030-72-10 TCWhy it fits: Oil seal 30×72: sleeve shaft 30, housing bore for the bearing 72; SN/SNL housings have their own seals, so check against the housing
      €0.392,205 pcs
    03

    Details

    what this bearing is, questions

    About the bearing

    d×D×Bsize 35 × 72 × 23mm
    Cdynamic 30.7kN

    Self-aligning ball bearing 2207 K. Under GOST the same bearing is designated 111507.

    C: SKF data. Another brand publishes its own figures, so compare them against that brand’s catalogue.

    Frequently asked questions

    What is 111507?

    It is the same bearing under GOST 3189-89: 111507 corresponds to the ISO base 2207 K. Size 35 × 72 × 23 mm, a full equivalent of 2207 K.

    Will 2207 C3 fit instead?

    Same size, clearance greater than normal. C3 is used where the bearing runs hot or sits on the shaft with an interference fit. If the old bearing is not marked C3, take this one.

    Can I fit another brand instead of this bearing?

    Without checking, only an exact equivalent: the size, seal, clearance and design match according to the brand’s catalogue. Positions with the same geometry differ in seal, clearance or design, and each one says so in the equivalents block. Load ratings differ between manufacturers, so for a heavily loaded unit compare C.

    How do I get a price and a lead time?

    Press “Request a quote” and send the part number and quantity. We reply with the price, availability and delivery terms for your country.

    04

    Reviews

    No reviews yet