+34 637 212 975 Mon–Fri 8:00–17:00 Madrid time Wishlist0 Compare0
€0.00
Prices include VAT at the Spain rate (21%); the cart recalculates VAT for your delivery country. Excl. VAT: €2.39 per piece.
16014 · 70 × 110 × 13

Deep groove ball · 16014

radial — mediumaxial — low, on both sides
    Drawing of 16014: ⌀70 × ⌀110 × 13 mm16014
    Fig. 1: 16014, end view and section; rolling element geometry per the NSK catalogue. Dimensions in mm

    There is no photo of this product: the 3D model and drawing show the dimensions of 16014

    Load: radial medium; axial low, on both sidesDeep groove ball

    Bearing CT 16014

    €2.89per piece incl. VAT
    In stock: 598 pcs
    In the cart

    Specifications

    Manufacturer number
    GOST number
    Equivalents
    2 exact, 6 approximate
    d
    70 mm
    Bore diameter dBearing bore = shaft diameter. Source: two supplier sources
    D
    110 mm
    Outside diameter DOutside diameter = housing bore. Source: two supplier sources
    B
    13 mm
    Width BRing width. Source: two supplier sources
    Seal
    open, no protection
    Clearance
    normal clearance
    C
    29.1 kN
    Basic dynamic load rating CLoad for one million revolutions at 90 % reliability; the L10 life is calculated from it as (C/P)^p. ISO method, manufacturer’s figure: do not carry it over to another brand. Source: supplier data
    C0
    25 kN
    Basic static load rating C0Permissible load without rotation and under shock; ISO 76 method, manufacturer’s figure. Source: supplier data
    m
    0.43 kg
    MassWeight of the product. Source: supplier data
    01

    Equivalents

    the same size 70 × 110 × 13 from other brands

    8 products
    Series illustration (not a photo of this item): 16014
    You are viewingCT 16014
    €2.89baseline for the price comparison

    Everything the number specifies matches: series 160, 70 × 110 × 13 mm, open, no protection, normal clearance, ordinary steel, design without special letters. The codes in the number are read against the CT catalogue.

    • Series illustration (not a photo of this item): 1601416014This bearingCT70 × 110 × 13598 pcs€2.89you are here
    • Series illustration (not a photo of this item): 1601416014NSK70 × 110 × 13available to orderon request

    Under the price: the difference from the price of this bearing (€2.89).
    02

    Often bought with this

    seal 70×110, shaft snap ring Ø70, bore snap ring Ø110

    4 products
    • Seal 70×110JULU 070-110-10 TCWhy it fits: Oil seal 70×110: shaft 70 and housing bore 110, the same as the bearing
      €0.97330 pcs
    • Seal 70×110JULU 070-110-12 TCWhy it fits: Oil seal 70×110: shaft 70 and housing bore 110, the same as the bearing
      €1.05180 pcs
    • Shaft snap ring Ø70CT SEG 70 Z by1000Why it fits: DIN 471 snap ring for a 70 shaft: holds the inner ring on the shaft
      €209.55out of stock
    • Bore snap ring Ø110CT SEG 110 W by 100Why it fits: DIN 472 snap ring for a 110 bore: holds the outer ring in the housing
      €51.47available to order
    03

    Details

    what this bearing is, questions

    About the bearing

    D 110d 70B 13
    d×D×Bsize 70 × 110 × 13mm
    Cdynamic 29.1kN
    C0static 25kN
    mweight 0.43kg

    Deep groove ball bearing 16014. Under GOST the same bearing is designated 7000114.

    C, C₀, m: CT data. Another brand publishes its own figures, so compare them against that brand’s catalogue.

    Frequently asked questions

    What is 7000114?

    It is the same bearing under GOST 3189-89: 7000114 corresponds to the ISO base 16014. Size 70 × 110 × 13 mm, a full equivalent of 16014.

    Will 16014 C3 fit instead?

    Same size, clearance greater than normal. C3 is used where the bearing runs hot or sits on the shaft with an interference fit. If the old bearing is not marked C3, take this one.

    Can I fit another brand instead of this bearing?

    Without checking, only an exact equivalent: the size, seal, clearance and design match according to the brand’s catalogue. Positions with the same geometry differ in seal, clearance or design, and each one says so in the equivalents block. Load ratings differ between manufacturers, so for a heavily loaded unit compare C.

    How do I get a price and a lead time?

    Press “Request a quote” and send the part number and quantity. We reply with the price, availability and delivery terms for your country.

    04

    Reviews

    No reviews yet