+380 50 364 66 46 Mon–Fri 8:00–17:00 Kyiv time Wishlist0 Compare0
Prices are in euros. The final price and delivery cost are confirmed in the quote.
Drawing of 6003 ZZ: ⌀17 × ⌀35 × 10 mm6003 ZZZZ
Fig. 1: 6003 ZZ, end view and section; rolling element geometry per the NSK catalogue. Dimensions in mm

There is no photo of this product: the drawing shows the dimensions of 6003 ZZ

Load: radial medium; axial low, on both sidesDeep groove ball

Bearing Z&S 6003 ZZ

€0.79per piece
Available to orderThe manager confirms the lead time
Request a quote

Specifications

Manufacturer number
ISO designation
GOST number
Equivalents
10 exact, 38 approximate
d
17 mm
Bore diameter dBearing bore = shaft diameter. Source: two supplier sources
D
35 mm
Outside diameter DOutside diameter = housing bore. Source: two supplier sources
B
10 mm
Width BRing width. Source: two supplier sources
Seal
ZZshields, both sides
Clearance
normal clearance
C
6.37 kN
Basic dynamic load rating CLoad for one million revolutions at 90 % reliability; the L10 life is calculated from it as (C/P)^p. ISO method, manufacturer’s figure: do not carry it over to another brand. Source: supplier data
C0
3.25 kN
Basic static load rating C0Permissible load without rotation and under shock; ISO 76 method, manufacturer’s figure. Source: supplier data
Limiting speed
24,000 rpm
Limiting speedMechanical limit; depends on the seal (SKF 6200: 36,000 open, 17,000 with 2RSH). Source: supplier data
m
0.039 kg
MassWeight of the product. Source: supplier data
01

Equivalents

the same size 17 × 35 × 10 from other brands

49 products
Photo: 6003 ZZ
You are viewingZ&S 6003 ZZ
€0.79baseline for the price comparison

Everything the number specifies matches: series 60, 17 × 35 × 10 mm, metal shields on both sides, normal clearance, ordinary steel, design without special letters. The codes in the number are read against the Z&S catalogue.

Under the price: the difference from the price of this bearing (€0.79).
02

Details

what this bearing is, questions

About the bearing

D 35d 17B 10
d×D×Bsize 17 × 35 × 10mm
Cdynamic 6.37kN
C0static 3.25kN
mweight 0.039kg

Deep groove ball bearing 6003-ZZ, design ZZ: metal shields on both sides. Under GOST the same bearing is designated 80103.

C, C₀, m and limiting speed 24,000 rpm: Z&S data. Another brand publishes its own figures, so compare them against that brand’s catalogue.

Frequently asked questions

How does 2RS differ from ZZ?

2RS has rubber seals that touch the inner ring and keep out dust and water better, which is the usual choice for field machinery. ZZ has metal shields that do not touch, allow higher speeds, and protect against dirt less well.

What is 80103?

It is the same bearing under GOST 3189-89: 8 — metal shields on both sides, 0103 corresponds to the ISO base 6003. Size 17 × 35 × 10 mm, a full equivalent of 6003-ZZ.

Will 6003 ZZ C3 fit instead?

Same size, clearance greater than normal. C3 is used where the bearing runs hot or sits on the shaft with an interference fit. If the old bearing is not marked C3, take this one.

Can I fit another brand instead of this bearing?

Without checking, only an exact equivalent: the size, seal, clearance and design match according to the brand’s catalogue. Positions with the same geometry differ in seal, clearance or design, and each one says so in the equivalents block. Load ratings differ between manufacturers, so for a heavily loaded unit compare C.

How do I get a price and a lead time?

Press “Request a quote” and send the part number and quantity. We reply with the price, availability and delivery terms for your country.

03

Reviews

No reviews yet